Bryter 1-veis - HE-HLS01

Z-Wave Plus V2 1-veis bryter for innfelt montering fra Heltun - HE-HLS01.

The High Load Switch with Thermostat Functions brings incredible capabilities to any connected device. It makes electric outlets and whole banks of lights ‘smart’ with full remote monitoring, control, and advanced programmability. You can now enable Internet-connected thermostat functions where a local display and controls are not needed, such as with roof or driveway de-icing systems, etc. This brings the convenience of smartphone app control and programmability to ‘dumb’ devices such as electrical outlets & panels, electric water heaters, radiators, fireplaces, and radiant floor or de-icing systems.
At 26mm in depth, the High Load Switch is also impossibly small, fitting into any rectangular, round or square electrical junction box, even behind an attached device. You can connect an NTC temperature sensor to monitor ambient or radiant floor/roof system temperatures. This sensor can be installed on the wall, under floorboards, on the roof, or under decking, allowing you to accurately measure surface temperatures. So long the HELTUN High Load Switch is fully compatible with NTC sensors from other manufacturers, so there is no need to replace an existing sensor when installing it.
You can also control the High Load Switch by connecting it to an external system - like an alarm system - using a pilot wire which could be programmed to automatically reduce the temperature when the house is empty or turn on electric outlets/lights when people come home.

• Communicates via Z-Wave Plus V2 RF (868,42 MHz)
• RF Range Typical: up to 100m in a free field, up to 30m in buildings
• Standard and enhanced security: Non-Secure, S0 and S2 Unauthorized, S2 Authorized with Key
• Over The Air (OTA) firmware upgrades
• Group for Association: 4 (Group 1 support 1 node; Group 2 - 4 supports 5 nodes)
• Relay switching with HELTUN Advanced Zero-Crossing Technology
• Maximum resistive load: 16A, 4000W @ 220V
• Measured temperature range: -30°C to +80°C
• Temperature measurement accuracy: ±0.5°C
• Six operation modes: COM, ECO, VAC, DRY, TIME, MANUAL
• Four Schedules: Morning, Day, Evening & Night
• Time & Temperature Set Point (Heating Devices)
• Time Only (All Other Devices)
• Eight relay modes: Invert State, Momentary, Momentary Reversed, Switch ON Only, Switch OFF Only, Switch to Mode, Timer (ON then OFF), Timer (OFF then ON)
• Three Safety Modes with Notification & Auto Shutoff: Overload (auto-shutoff on overload), Overheat (auto-shutoff on outlet over-temp), High Load Timeout
• Energy consumption meter
• Power consumption: <1W
• Can be used with different external NTC temperature sensors: 1kΩ – 100kΩ
• Temperature sensor calibration
• Temperature set intervals: 4°C – 37°C

VIKTIG! Kan kun installeres av en autorisert elektroinstallatør fra registrert installasjonsvirksomhet. Varmekabler, varmekabelmatter og varmefolien må legges av en profesjonell (ellers underlaget og selve gulvet kan du legge selv). Privatpersoner som ønsker selv utføre arbeid på det elektriske anlegget må studere først info fra dsb (Direktoratet for samfunnssikkerhet og beredskap) - Elektrisk arbeid: Dette kan du gjøre selv

Merk: Gulvføleren bør legges i et plast installasjonsrør som støpes (freses) ned i gulvet. Dette røret skal legges så høyt som mulig i støpen (mot gulvet). Følerkabelen kan forlenges med sterkstrømskabel. Følerkabelen bør ikke legges parallelt med kabler som fører store strømmer, da dette kan indusere uønskede signaler.

OBS! Det er et krav at tregulv med elektrisk gulvvarme må ha en temperaturføler installert. Maksimal gulvtemperatur bør ikke overskride 27°C.

Klikk her for å besøke Heltun Supportsiden for Z-Wave 700 Bryter 16A - HE-HLS01