Termostat - HE-HT01

Z-Wave Plus V2 kontrollert Termostat - HE-HT01 fra Heltun.

The HELTUN HE-HT01 Advanced Programmable Thermostat for Heating systems can be flush mounted over standard electrical junction boxes. It is designed to maintain a constant room temperature by providing sensors for both ambient and radiant floor heating systems. It is recommended for control of electric heating systems (radiator, convection, electric fireplace), boilers, or electric underfloor heating. Heating elements are directly controlled by a single-pole switch. The maximum load for the HE-HT01 thermostat is 16 Amps (4000W @ 250VAC) which must be connected through a circuit breaker.
The HE-HT01 has an LCD screen, six sensitive capacitive touch control buttons, and two temperature sensors (for ambient air temperature and an external NTC floor sensor). It is also equipped with built-in sensors for humidity, illumination, and energy consumption.
The HE-HT01 integrates a Z-Wave 700 platform module allowing it to be used with Z-Wave home automation systems. The HE-HT01 supports Z-Wave ‘S0’ and ‘S2’ security protocols, SmartStart technology, and can be connected (“associated”) to ten other Z-Wave devices, such as relays, switchers, etc. You can select one of six operation modes either manually, or by using a Z-Wave controller/gateway. As a safety measure, the HE-HT01 protects radiant floor systems from overheating by automatically switching off if the temperature reaches 40°C.
The display has a user-friendly interface, showing: ambient air temperature, floor temperature, user set point, humidity level, current operating mode, time, day of the week, and status of the Z-Wave network and relay. Display brightness adjusts to ambient light conditions automatically making it always easy to read.

• Communicates via Z-Wave Plus V2 RF (868,42 MHz)
• RF Range Typical: up to 100m in a free field, up to 30m in buildings
• Standard and enhanced security: Non-Secure, S0 and S2 Unauthorized, S2 Authorized with Key
• Over The Air (OTA) firmware upgrades
• Group for Association: 2 (Group 1 support 1 node; Group 2 support 5 nodes)
• Relay switching with HELTUN Advanced Zero-Crossing Technology
• Display: LCD-display 73 x 42mm, black with white icons
• Display brightness adjustable feature
• 6 Heating Modes
• Hysteresis adjustable range: 0,2°C to 10°C (default: 0,5°C)
• Measured temperature range: -30°C to +80°C
• Temperature measurement accuracy: ±0.5°C
• Can be used with different external NTC temperature sensors (1 - 100 kOhm)
• Floor temperature sensor NTC (10 kOhm, 3 meters length) included
• Temperature set intervals: 1.0°C to 37.0°C
• Measured humidity range: 0 - 80% RH
• Humidity measurement accuracy: ±3.0% RH
• Internal ambient light sensor measuring range: 0 - 30000 Lux
• External input trigger feature
• Child lock feature
• Energy consumption meter
• Maximum resistive load: 16А, 4000W @ 250VAC
• Power Supply: 85-265VAC 50/60Hz, 24-48VDC
• Power Consumption: 1W

VIKTIG! Kan kun installeres av en autorisert elektroinstallatør fra registrert installasjonsvirksomhet. Varmekabler, varmekabelmatter og varmefolien må legges av en profesjonell (ellers underlaget og selve gulvet kan du legge selv). Privatpersoner som ønsker selv utføre arbeid på det elektriske anlegget må studere først info fra dsb (Direktoratet for samfunnssikkerhet og beredskap) - Elektrisk arbeid: Dette kan du gjøre selv

Merk: Gulvføleren bør legges i et plast installasjonsrør som støpes (freses) ned i gulvet. Dette røret skal legges så høyt som mulig i støpen (mot gulvet). Følerkabelen kan forlenges med sterkstrømskabel. Følerkabelen bør ikke legges parallelt med kabler som fører store strømmer, da dette kan indusere uønskede signaler.

OBS! Det er et krav at tregulv med elektrisk gulvvarme må ha en temperaturføler installert. Maksimal gulvtemperatur bør ikke overskride 27°C.

Klikk her for å besøke Heltun Supportsiden for Z-Wave 700 Termostat - HE-HT01